Just How to Set up a Tub
View WebsiteWhat're your thoughts about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bath tub isn't precisely brain surgery, however it does require strong plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard project. If the old bathtub is readily obtainable, the job can relocate rapidly; if you need to open a wall surface to remove the old bathtub and place the new tub, the job is much harder. In either instance, the project is within a house handyman's abilities, although you will require a helper to leave the old bathtub as well as embeded in the new one. Make certain you have actually qualified on your own for the job as well as fit attempting it. Instead of working with a professional to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you start. Chances are you may require a professional plumber to make tube connections.
This write-up will assist you mount a brand-new bathtub in your shower room if you have actually already purchased a brand-new bathtub and don't require to transform the arrangement of your previous water system pipelines.
Your devices and material list need to comprise the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, activate the faucets to drain any water staying in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipes. Once the supply pipes have been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Before proceeding to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin making sure that the washers remain in area between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former type needs to be attached to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bathtub
Making use of the two wooden boards under its feet, position the tub in the required placement. The wooden boards are helpful in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 little points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by examining the level and readjusting the feet on the bathtub till the spirit level reviews level.
To set up taps, fit all-time low of the furthest versatile tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the water supply and also examine all joints and brand-new pipework for leaks and also tighten them if necessary. Load the bathtub as well as also inspect the overflow electrical outlet as well as the regular outlet for leakages.
Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling and also sealing around the tub needs to wait up until the bath tub has been utilized at the very least once as this will certainly resolve it into its last placement.
Getting ready for the Installment
Firstly, the supporting structure supplied with the bath needs to be fitted (if required) according to the producer's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps unit to avoid pressure on the bathtub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, causing problems with moisture as well as possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your components as well as fittings. They are sold in tubes as well as cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the bath tub with water prior to securing, to enable the motion experienced when the tub is in use. The sealant can crack rather very early if you do not think about this activity prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly available on the market. It is advisable to fit the floor tiles utilizing water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen person who reads about Installing A Bathtub, I was thinking sharing that post was really useful. Those who liked our post plz make sure you remember to share it. I appreciate reading our article about How to Install a Bathtub.
Schedule Services